Well Pump Installation Cost: Complete 2025 Price Guide

Installing a well pump requires assessing specific factors like pump type, whether submersible or jet, and well depth in feet, as these determine costs. For most residential setups, budget $400-$2,500 upfront; this range narrows based on those key details. You’ll want to check the exact model and its PSI rating before making a decision.

This page maps out where your job falls in that range, what components drive cost up, and which pages have the specific step-by-step details.

Video: “How to Install or Replace A Well Pump. Professional Guidance” by H2O Mechanic

Quick cost overview

Here’s how installation costs break down by pump type:

Pump Type	Pump Cost	Labor	Total
Submersible (shallow, under 100 ft)	$300-$600	$200-$400	$500-$1,000
Submersible (deep, 100-300 ft)	$400-$800	$300-$600	$700-$1,400
Shallow jet pump	$100-$250	$100-$300	$200-$550
Deep-well jet pump	$150-$350	$150-$400	$300-$750

These figures cover the pump itself and basic labor. They don’t include a new pressure tank ($200+), a replacement pressure switch ($25), or a pump controller ($75). All are common add-ons when the whole system is being serviced.

Brands matter too. Franklin Electric, Grundfos, and Goulds sit at the mid-to-premium tier and are the most common residential pump brands. CountyLine (sold through Tractor Supply) is the economy option, adequate for seasonal properties.

Who this guide is for

:

• You’re replacing a failed well pump and want to understand total costs
• You received a contractor quote and want to know if it’s reasonable
• You’re planning a new home construction with a private well
• You want to understand what components beyond the pump might need replacing

Common mistake.

This guide isn’t for you if:

• You have no water right now and need emergency troubleshooting: see our
  well pump repair troubleshooting guide
  first
• Your pump runs but pressure is low (that’s usually the pressure switch or tank, not the pump)

Cost by pump type

Submersible pumps (most homes)

Submersible pumps, costing around $300 to $500, typically power any well deeper than 25 feet, their motors and impellers fully immersed at the bottom of the well casing. This setup ensures they handle heavier loads but comes with a higher initial installation price due to the need for lowering and raising equipment from within the well.

A submersible pump installation costs $500-$1,400 total for most residential wells. The pump itself runs $300-$800 depending on the GPM rating and brand. Well depth drives labor cost: a 50-foot well takes one hour of work. A 300-foot well requires lifting equipment and takes 3-4 hours.

Pay attention.

Grundfos and Goulds pumps cost more upfront but routinely outlast economy brands by 5-8 years. Franklin Electric is the most common mid-tier choice for residential work.

See our
DIY well pump installation guide
for the full step-by-step if you’re considering doing the job yourself.

Jet pumps (shallow wells only)

Jet pumps mount above ground and are only used with wells shallower than 25 feet (shallow jet) or up to 90 feet (deep-well jet). They’re less expensive to install because there’s no in-well work involved.

A shallow jet pump replacement costs $200-$550 all-in. These are the most DIY-friendly option. The pump mounts to the pressure tank, the connections are visible. The job doesn’t involve lifting anything from a well.

Small detail, real impact.

See our
full replacement cost breakdown
for a complete itemized list by pump type.

What drives the price up

Beyond pump type and depth, these factors push installation costs higher:

Depth is the biggest one. Every 100 feet of additional depth adds $50-$100 in drop pipe and wire, plus $50-$150 in labor. At 200+ feet, a pump puller or tripod is required. We’ve found that the depth cost adder surprises most homeowners who only budgeted for the pump price they saw online, so build that into your estimate upfront.

Pressure tank condition matters more than most homeowners expect. A waterlogged pressure tank can’t be repaired, only replaced. If water discharges from the air valve when you press it, budget $200-$500 for a new one. Replacing it while the well is already open is cheaper than two separate service calls. See our
pressure tank sizing and cost guide
for what to look for.

Permits add $50-$300 depending on the jurisdiction. Many states require a licensed well driller for any in-well work.

Labor rates vary more than the pump price does. Rural areas with few licensed well drillers often charge more than suburban markets. Get at least two quotes before committing.

DIY vs professional installation

Shallow jet pump replacement is viable DIY for most mechanically capable homeowners. The pump mounts above ground, connections are standard plumbing fittings. The job takes 2-4 hours.

When replacing a submersible pump, consider the depth of your well, anything deeper than 50 feet and you risk a $300-$1,000 bill if the pump falls into the casing. You’ll need to lower it carefully on a drop pipe and safety rope; otherwise, recovery can be tricky and costly. Better to call a professional to handle any submersible pump issues in deep wells.

If you do hire out, ask the contractor to quote the pump separately from labor. Professionals often mark up parts 20-40%. Knowing the pump model lets you verify the price independently. We recommend getting at least two quotes and asking each contractor which pump brand and model they plan to install, since quotes that bundle parts and labor make it impossible to comparison-shop the pump itself.

Installation vs replacement cost

Failing pumps in existing wells require different steps compared to installing a new one. Drilling expenses range from $15 to $30 per foot for new well projects, meaning a 150-foot deep hole could cost between $2,250 and $4,500 without factoring in pump prices. Ensure the existing pressure tank supports the pump’s minimum PSI rating; otherwise, an upgrade might be needed.

For an existing well, you’re paying only for the pump, components, and labor. Replacement is the more common and more affordable scenario.

After replacement, priming is a required step for jet pumps (submersible pumps self-prime). See
how to prime a well pump
for the exact procedure.

FAQ

How much does it cost to install a well pump?

Pump installation for a shallow well, around 50 feet deep, might see you paying anywhere from $200 to $550; the jet pump type skews lower in this range. Deeper wells, say between 100 and 300 feet, call for submersible models that will set you back approximately $700 to $1,400, labor included. Remember, failing to check the PSI rating before purchasing could mean an undersized pump trips the breaker, costing more in replacements down the road.

How long does well pump installation take?

A shallow jet pump replacement takes 2-4 hours for a professional. A submersible pump in a well under 100 feet takes 3-5 hours. Deep submersible jobs (200+ feet) can take a full day, especially if old pipe and wire must be pulled and replaced.

Can I install a well pump myself?

Shallow jet pumps are viable DIY projects for homeowners comfortable with basic plumbing. Submersible pumps in wells deeper than 50 feet carry significant risk. A dropped pump during installation costs hundreds to retrieve. Many states also require a licensed well driller for in-well work.

What is the lifespan of a well pump?

A well pump typically lasts 8-15 years. Premium brands like Grundfos and Goulds frequently reach 15 years in residential applications. Economy pumps running in high-demand or heavy-sediment wells often fail before 10 years.

Does insurance cover well pump replacement?

Standard homeowner’s insurance doesn’t cover well pump replacement due to normal wear and failure. Some policies cover sudden and accidental damage (like pump failure from a lightning strike), but equipment breakdown or age-related failure is excluded. Check your policy’s “other structures” and equipment breakdown riders.

---

For site-wide resources on private water systems, visit
HomewellFix
.